[Video] How to install WCAC and WCAP
Please refer to the youtube video
Configurate Multiple PtP for Backhaul
The topology is like this, as follows.
For example, we use two pairs of G5250 as backhaul links and using Huawei switches to make the two link together.
Noted: Your switch must support link aggregation function.
First open the link aggregation function on your
Configure a Layer-2 Point-to-Point Link by 11AC device
Here is the steps about how to configure a PtP link by 11AC.
The network topology is like this.
Step 1 , Configure the 192.168.1.2 as an AP. Login in and set the LAN IP.
Configure VLAN tag on 802.11ac Device
Set up several VLAN that each VLAN for the
different department of a company and each VLAN has a SSID different from
are the steps.
enter the management window. Click the NETWORK -> Interface -> LAN Interface -> Add the VLAN . &nb
Configure VLAN tag with multiple ssid
Set up several VLAN that each VLAN for the different department of a company on the AP.
Here are the steps.
1. First enter the management window. Click the NETWORK -> VLAN -> Add .
2. Put in the VLAN ID then cli
[Video] How to use WiController Part 3: Massive upgrade firmware
If you cannot see the video below, click https://youtu.be/UbeIKgC5eKU
[Video] How to use WiController Part 2: Apply the Config Templates
The video is showing how to use WiController to apply configuration to multiple devices. Check the WiController manual for choosing the device type before applying the settings!
[Video] How to use WiController Part 1: Discover device
[Video] How to use Wimanager for firmware massive upgradeFor the reason why set IP address like that in the video, refer to the link
Step 1. IP Setting
Step 2. FTP server Setting
Step 3. Wimanager Setting
Step 4. Upgrade and wait, done!
[Video] How to install Wisnetworks Sector Base Station
The video is showing the hardware installation for WIS-L2415S/WIS-L2417S and WIS-L5819S/WIS-L5820S. If you can't see the video, you can click the link below
[Video] How to install Wisnetworks Panel Bridge & Base Station
The video is showing the hardware installation for
Base Station: WIS-L5818S/WIS-L2416S/WIS-L5800N
Panel Bridge: WIS-L5819D/WIS-L2415D/WIS-L5825D
If you can't see the video, you can click the link below
Configure VLAN on a PtP Link
In this example, you should first refer to Configure a Layer-2 Point-to-Point Link , referring to the following link
The network and IP setting is showing below
[Video] How to install WIS-G5250/WIS-D5250?
The video is showing the hardware installation for WIS-G5250 and WIS-D5250. If you can't see the video, you can click the link below
[Video] How to configure a TDMA base station?
The video is introduced the basic software settings for radio and network, mainly help to configure an access point/base station.
If you can't see the video, you can click the link below
[Video] How to configure a station connecting to AP?
The video is introduced the basic software settings for radio and network, mainly help to configure the radio as station mode and connecting to an access point, verifying the linked up status.
If you can't see the video content, you can click the link be
Connecting with Mikrotiks base station
Before the connection, make sure the Mikrotiks TDMA protocol is turned off like below.
If the nstreme or nv2 is enabled, only Mikrotiks devices can connect to each other.
1) Use winbox, setting the Mikrotiks device IP address to 192.168.1.1
Connecting with UBNT devices
First before connecting, the Airmax should be turned off like below
Setup with UBNT as Access Point
1) In this case the Wisnetworks product works as station or station WDS . Make the UBNT device as Access Point and choose an encryption.
2) Login the
Configure a Long Range PtP Link with Indoor Wireless Coverage
In this example, you should first refer to Configure a Layer-2 Point-to-Point Link and Configure a Long Range Wireless CPE
click the diagram for higher resolution view.
1) Connect to the base station using a CPE. The example here is
Configure a Long Range Wireless CPE
1. After login the web interface, go to Wireless page, press scan
wait for several seconds you can see the base station list, choose your base station and press the ssid
back to the wireless page, find the advanced setting->distance, fill in
Configure a Point-to-Multipoint (PtMP) Layer-2 Network
1.First, set your computer's wired network with static IP of 192.168.1.x (x should be any one of 100~254, such as 192.168.1.100). This computer is used to setting the radios.
2.Using a web browser, enter 192.168.1.2 as the "URL" to gain access to the radio's manageme
Powerful Features Free to Use
Wisnetworks spectrum analyzer is a revolutionary product which integrated in all Wisnetworks radios. It's useful in studying all RF energy contributors in the 2.4GHz/5GHz band, but has particularly useful tools that make it ideal for optimizing wireless networks
AP WDS Repeater
The outdoor basestation does not always have a wired backhaul connection, thus a very quick and robust network deployment is required for all the radio. With the AP repeater feature, up to 7 access point can be connected together to provide a large size coverage area, with no wire
Wisnetworks zero sense roaming Technology
Zero sense roaming Introduction
Zero Sense Roaming is a kind of WLAN optimization function for application of fast moving and seamless switching. Wisnetworks zero sense roaming technology can meet the needs of zero packet loss switching between AP for wireless stations/clients. Common ap
WiD TDMA Technology
The WiD TDMA technology is a huge benefit and allows the scaling of many more clients than legacy 802.11 CSMA. This allows the access point to get up to 100 wireless users while still maintain reliable connections, even in noisy RF environment.
In another hand, the 2*2 MI
MRF Smart Antenna ArrayWhile the wireless signal travels in open space, the obstacle will cause signal refraction, diffraction and scattering, multipath fading, etc. Those influences would finally make the signal totally different at the receiver side.
MRF smart antenna technology using the uniqu
How to launch Spectrum Analyzer?
If you cannot see the video, click the link below
[Video] Reset the radio using WiController
WiController - Configuration - Configuration - Restore factory default
WiController Config Templates Rescan no result
Recently some customer feedback that there is some problem applying the settings to the radios by WiController.
The specific phenomenon is that WiController can't find the radio after finishing the AP templates. While clicking the Rescan button there is no radio discovered.
Note for AP Repeater mode
All APs in AP‑Repeater mode (WDS Peers) must operate on the same frequency channel, use the same channel spectrum width, and share the same security settings.
For AP‑Repeater mode, the WPA™/WPA2™ security methods will not work ; instead, us
How to reset radio by telnet?
For all Wisnetworks radio, there is a command at telnet which can quickly reset the radio. After login the radio input
rm -rf /etc/sysconfig/*
then reboot the radio
How to get known the signal quality?
Compared to most of the radio on the market, we have a alternative method to judge the signal quality using tx/rx/total busy.
Rx Busy : This is the most important value to judge the percentage of interference. In this condition, the Rx Busy is 18%, means the signal would have
Radio connected, but very poor/ping loss/low throughput
This is a FAQ problem and there are something should be checked.
The first thing you should do, is use RF calculator to check if the calculated result is equal to your test result. If everything shows alright, go on checking.
Only more t
Why can't two radio be connected?
For base configuration, refer to the link below
>>Configure a P2P link with Wisnetworks Radio
1. Make sure the radio is OK
Test indoor or outdoor close range first with two radio, see if can be connected and ping/running through
How to setup zero sense roaming
AP Side Configuration
AP will not set relative parameter of roaming, but must meet the following conditions:
Wireless working mode of AP must be AP-WDS mode;
AP channel of all involved zero sense roaming must be the same;
SSID of a
Wisnetworks PtP Radio Throughput v.s. Range Test
The test is based in real environment test result, with clear line of sight and no co-frequency interference
Test tool using IX Chariot, not the software internal speed test tool
Wisnetworks reserves the right of final explanati
Read First: 5MHz/10MHz channel width
If some cases you need to use 5/10MHz channel bandwidth, read the following guide first. Otherwise there might be some unexpected issues.
Go to Radio page, choose the bandwidth you required, such as 10MHz.
And here is the most important , go to a
Antenna Height v.s. Range
Download the PDF Version
Wisnetworks Radio Selection Guide
Download the PDF Version
How to configure the Wimanager?
For the Wimanager configuration guide, you can refer to the link below
>>Download the guide
Download Wimanager (Press the link below)
How to login the device if forgetting the device IP address?
Basically, if you still remember the IP range like 192.168.1.x, you can use our Wimanager to scan the IP address. But if you change the IP to 10.x.x.x style and totally forgetting the IP range, here is another alternative method to help you login the configuration webpage.